2020-9-28
网站首页 关于我们 产品中心 新闻资讯 在线留言 联系我们  
公司产品
代理产品

上海曼升电子科技有限公司
联系人:达多鹏
手机:13482606296
电话:021-54337861
传真:021-54148519
公司QQ  1017863166   1217545386 
邮箱:mansheng@shmsdz.com
网址:www.shmsdz.com
地址:上海市闵行区景联路1238弄501-508室

您现在的位置: 产品中心
当前位置:产品中心 >> 变送器、数显表 >> R010电位器讯号变送器
R010电位器讯号变送器[返回]
量測電位計:1~10KΩ

工作电压:16-30 VDC

输出信号:0-10 VDC

适合于任意型号之电子尺(4-pin接头式)

 

Special features

interface module for TLH and

LWH position transducers

sensor proximity in the plug

connection

interference-free signal

transmission

standardized output signals

0…10 V

±…10 V

0…20 mA

4…20 mA

excellent linearity

extremely low temperature drift

30 ppm/K (typical value)

zero point and range optionally

adjustable or fixed

The signal conditioner supplies

the position transducer with a

highly stable, constant voltage.

The wiper signal is picked off

without load via a high-resistance

input stage and transformed into

a displacement-proportional

standardized output signal.

The excellent linearity, low tem-

perature drift and sensor-proximity

of the signal conditioning process

ensure full utilization of the out-

standing benefits of the position

transducers, guaranteeing

reliable, interference-free

transmission of signals over long

distances.

In the adjustable models, the

zero point and range can be

adjusted within wide limits using

spindle trimmers. This permits

standardized output signals to

be adjusted even if the maximum

path of the transducer is not

completely utilized.

The electronic circuitry is inte-

grated into a socket to fit the

DIN 43650 appliance plug. A

wide range of operating voltages

can be supplied by an unstabi-

lized direct voltage source.

Selected SMD components

with a wide temperature range

guarantee maximum operating

reliability even under extreme 

environmental conditions.

The MUW is connected by

means of a four-pole terminal

strip. It is possible to orient the

connecting cable as required by

turning the housing insert in 90°

steps.


Mechanical Data

Dimensions                     see drawing

Protection class                  IP 65 (DIN 400 50 / IEC 529)

Screw-type terminals              0.5        mm2

Recommended cable

dia. 4 - 10 mm                   3- or 4-core twisted with protective braiding

Weight                         appr. 75     g
Electrical Data

Operating voltage                18…30     VDC

Input resistance                  > 10       MΩ

Reverse voltage protection

integrated

Current consumption              max.      35 mA

Internal reference voltage for the

position transducer,

highly stable and short circuit-proof   > 10    VDC

Permissible connection resistance

of the position transducer          700  

Adjustment rangeZero point        10        %

Gain                           1…2

Linearity                        0.01 (typical) %

Temperature coefficient*          30 (typical) ppm/K

Temperature range               -25...+70  °C

*The TC applies for current and voltage outputs. If, at current outputs, the voltage is picked off at

the load resistor, the TC of the resistor must also be taken into consideration.

Connection diagram

 

网站首页 | 关于我们 | 产品中心示 | 新闻资讯 | 在线留言 | 联系我们
沪ICP备14050805号-1 版权所有 Copyright(C)2014 上海曼升电子科技有限公司 网站建设:企炬